CLUSTERS
The server availability index is approximately equal to the percentage of the total server capacity that is still available. For example, if the server availability index is 65, you still have approximately 65% of the capacity of your server available. Although the servers in your enterprise may vary in power and resources, the server availability index represents the same thing on each server -- the amount of total availability of that server that is still available.
The server availability index is based on the expansion factor, which indicates the current workload on a server. The expansion factor is determined by comparing recent response times for specific types of transactions to the minimum time in which the server has ever completed the same types of transactions. For example, if the server is currently averaging 12 microseconds to perform Database Open transactions but the minimum time the server has ever performed a Database Open transaction is 3 microseconds, the expansion factor for Database Open transactions would be 4 (the current time of 12 microseconds divided by the fastest time of 3 microseconds). In other words, the expansion factor determines how many times longer it takes for a transaction to complete currently than it takes under optimal conditions.
IBM® Lotus® Domino® stores the minimum time for each type of transaction in memory and in the LOADMON.NCF file, which the server reads each time it starts. When the server shuts down, Domino updates the LOADMON.NCF file with the latest information.
To determine the current expansion factor, Domino tracks the most commonly used types of Domino transactions for specified periods of time. By default Domino tracks these transactions for 5 periods of 15 seconds each. Domino then determines the average time it took to complete each type of transaction and divides that time by the minimum time it ever took to complete that same type of transaction. This determines an expansion factor for each type of transaction. To determine the expansion factor for the entire server, Domino averages the expansion factors for all the types of transactions, giving a heavier weighting to the most frequently used types of transactions.
As the server gets busier, adding more load has an increasingly greater effect on performance and availability. Thus, adding more load to a busy server increases the expansion factor faster than adding more load to a less busy server.
Because servers differ in speed, capacity, and power, servers also differ in the workload they can handle. Therefore, the same expansion factor on two different servers does not necessarily indicate the same workload relative to the ability of the servers. For example, on a small server that takes a long time to perform transactions when the server is otherwise idle, an expansion factor of 40 might indicate that users are waiting many seconds for responses. On a very large, fast server, however, an expansion factor of 400 might indicate that users are waiting less than a second for responses.
How the availability index compares to the expansion factor To determine the availability index, Domino uses a formula that converts the expansion factor into an approximation of the percentage of the total server capacity that is still available. The following table shows a few examples of expansion factors converted to availability indexes.
Note The values in the table are based an expansion factor of 64 indicating a fully loaded server.
Changing the value of the expansion factor that indicates a fully loaded server To use Domino workload balancing effectively, you must adjust the relationship between the expansion factor and the availability index so that servers fail over when they reach the workload at which you want them to fail over. You do this by specifying the expansion factor value that you want to represent a fully loaded server. The default value in Domino is 64. When the expansion factor reaches that value, the server is considered to be fully loaded, and the availability index drops to 0 (zero).
Note You can use the Show AI server command to view a suggested availability index setting.
If your server is particularly powerful and fast, you might want to increase the value of the expansion factor that is considered fully loaded. On some very fast servers, you might want to make this value several hundred or higher. If your server is particularly slow, you might want to decrease this value.
To change the expansion factor value that indicates a fully loaded server, add the following setting to your NOTES.INI file, and then restart the server.
SERVER_TRANSINFO_RANGE=n
For the value of n, choose a number such that 2 raised to the power of n equals the expansion factor value that you want to indicate a fully loaded server. The default value for n is 6, which leads to an expansion factor value of 64 because 2 raised to the 6th power is 64. If you set SERVER_TRANSINFO_RANGE to 7, then the expansion factor value that indicates a fully loaded server becomes 128. If you set SERVER_TRANSINFO_RANGE to 8, the value becomes 256.
To determine the optimal value for SERVER_TRANSINFO_RANGE, do the following:
1. During a period of heavy usage, monitor the expansion factor on your server. You can use the console command "show stat server.expansionfactor" to do this. You can also monitor performance statistics during these periods. Record enough values for the expansion factor during heavy usage so that you can determine the expansion factor value you want to indicate a fully loaded server.
2. Determine a value for SERVER_TRANSINFO_RANGE such that 2 raised to the power of that value results in the expansion factor value you chose in step 1.
When you change the expansion factor value that indicates a fully loaded server, the relationship between the expansion factor and the availability index changes. The following table shows a few examples of expansion factors converted to availability indexes when the value of SERVER_TRANSINFO_RANGE is 8. The maximum expansion factor in this example is 256 because 2 raised to the power of 8 is 256.
Changing the amount of data used to compute the expansion factor Although it is not usually necessary, you can use the following NOTES.INI settings to change the amount of data that Domino collects in order to figure the expansion factor.